Mex-A2 — Circuits and Electronics
Nodal and mesh analysis of linear passive circuits: Kirchoff’s Laws, Thevenin and Norton equivalent circuits, maximum power transfer theorem. Semiconductor physics, p-n junction, diode circuits and applications. Transistors: Bipolar Junction Transistor (BJT) and Field Effect Transistor (FET). Transistors as linear devices and switches. Amplifier types and classes: bias circuits, small-signal equivalent circuits. Pulse-width modulation (PWM) control: conduction and switching losses in transistors. Operational amplifiers (op-amps): applications in analog signal conditioning for instrumentation and control. DAC and ADC. Op-amp comparators. Digital integrated circuits and logic families: TTL and CMOS.
Subject outline
Mex-A2 Circuits and Electronics is a technical exam (PEO National Examination 16-Mex-A2) in two parts, Part A Circuits and Part B Electronics. In Part A the December 2018 and December 2019 papers examine the equivalent resistance of a bridge and of a resistor ladder that needs a Y–Δ conversion, node-voltage equations with a supernode and a voltage-controlled source, superposition of dc sources and of sinusoidal sources, maximum power transfer from a circuit with a dependent source and to a conjugate-matched ac load, RC switching transients, ac node voltages at 60 Hz and the power a source delivers, and series and parallel RLC circuits solved by Laplace transform. In Part B they examine the output offset and gain of an op-amp T-network, a bridge rectifier fed by a square wave, a diode bridge with a zener and its transfer characteristic, common-gate and common-source MOSFET amplifiers, the enhancement-load NMOS and CMOS inverters with their transfer characteristics and noise margins, the slew rate, bandwidth and rise time of an op-amp follower, five BJT bias circuits that turn on whether the transistor is active or saturated, and five diode–op-amp circuits driven by a ±10 V sine. The study notes also take in mesh analysis, Norton equivalents, RL transients and the overdamped, critically damped and underdamped responses.
The paper is 3 hours and closed book: "This is a CLOSED BOOK EXAM. An approved Casio or Sharp model calculator is permitted." Each sitting sets eleven questions, six in Part A and five in Part B, and candidates answer either 3 questions from Part A and two questions from Part B or 2 questions from Part A and 3 questions from Part B, a total of five, indicating on the front page of the answer book which questions they want marked. All questions are of equal value, 20 each, and part marks are given for right procedures. Part A comes with "some useful equations and transforms": an appendix of Laplace pairs and the star–delta formulas, to which the December 2019 paper adds the first-order response, impedance, power and maximum-power relations. In Part B ground and chassis may be taken as common and op-amps as ideal unless stated otherwise; the December 2019 paper adds that supply voltages are ±15 V, a value the December 2018 paper leaves blank. Where a question is open to interpretation, the paper asks for a clear statement of any assumptions made.
What this course gives you
Worked solutions — all twenty-two questions from December 2018 and December 2019, eleven from each paper, every part, fully retypeset as live text and maths, with the final answers pulled out ahead of the working, each question's circuit as printed on the official paper, 46 authored diagrams and charts set into the solutions — circuits redrawn with their solved values, small-signal models, Laplace-transformed circuits, phasor diagrams, waveforms and transfer characteristics — and 10 worked tables. Both sittings have a published solution that answers every question, typed for the first two December 2018 questions and hand-written for the rest; each is transcribed with every number re-derived. Where the paper gives no numbers, in the two inverter questions (December 2018 Q10 and December 2019 Q10), the levels are derived symbolically and drawn for an authored example with VDD = 5 V and VT = 1 V, and the VOL that the December 2018 published solution leaves unsolved is worked out. 35 published steps do not survive checking, in 16 of the 22 questions, and each is flagged at the step that goes wrong — 19 in December 2018 and 16 in December 2019 — with the published working quoted beside the correction. Several change the final answer outright. In December 2018 the superposition total of Q2 is published as 2.389 V and is 12.10 V; the RC time constant of Q3 adds 5 kΩ and 10 kΩ in series where the capacitor sees them in parallel, giving 7.5 s for 1.667 s, and the sign of its initial slope is reversed; the source power of Q5 is computed as V × I and given an angle; the series RLC response of Q6 settles at −60 V where the capacitor settles at 10 V; the reservoir capacitor of Q8 is sized at 1,720 µF where the discharge lasts half a period and 860 µF suffices, and a diode that never conducts is given an average current of 0.3283 A; and three of the five BJT circuits of Q11 are saturated where the published solution assumes the active mode without checking. In December 2019 a controlling voltage is treated as a current, so all four node voltages of Q2 are wrong (V1 is −13.79 V, not 20.60 V); the Laplace transform of Q6 starts the capacitor at 80 V against the 5 V the question gives; and the MOSFET bias of Q8 sets the gate–source voltage equal to the threshold, which would carry no drain current. Nothing is silently overwritten: the published value is kept beside the correction. The December 2019 paper numbers its Part B questions (1) to (5); this course numbers them 7 to 11 and says so on each. Study notes — ten condensed topics — dc network reduction with bridges and Δ–Y; nodal and mesh analysis with supernodes and controlled sources; superposition, Thévenin/Norton and maximum power transfer; first-order RC and RL transients; Laplace-domain circuits and the second-order response; ac steady state, phasors and complex power; diode circuits, rectifiers and zeners; BJT dc analysis, active or saturated; MOSFET bias, small-signal amplifiers and inverters; and operational amplifiers, offset, slew rate and diode circuits — each naming the exam questions it serves, with 30 authored diagrams and charts and 11 tables between them. Practice & case studies — ten multiple-choice questions, each with a worked explanation, and five longer problems with complete worked answers and 15 figures: an unbalanced bridge solved by Δ–Y, an RL switching transient and its inductive kick, two loads at 60 Hz with power-factor correction, and two engineering case studies, sizing a 12 V bench supply and a 3.3 V logic pin driving a relay through a transistor. All fifteen are written for this course; none is taken from the two papers. Formula sheet — two pages, 37 relations in eight groups — dc circuits and network theorems, first-order transients, Laplace and second-order circuits, ac circuits and power, diodes, BJT, MOSFET and op-amps — with the relations the paper's own appendix prints marked as given. Both papers are closed book and neither names an aid sheet, so this is a sheet for revision: everything beyond the printed appendix has to be carried in your head. Printable resources — ten one-page reference cards — the exam appendix of Laplace pairs and star–delta formulas typeset, network theorems, a switching-transients checklist, s-domain element models, phasors and complex power, diode models and ripple, BJT bias (active or saturated), MOSFET regions and small-signal models, an op-amp circuit library, and an exam-day plan for choosing your five — plus four blank exam stationery templates. Reference links — twelve selected reference websites, among them the Engineers Canada syllabus page, PEO's technical exam program, MIT OpenCourseWare's 6.002 and 6.012 and four open LibreTexts textbooks, and fourteen chosen YouTube videos, each with a note on what it covers. Practice papers — the two question papers on their own, unmarked, 12 and 11 pages, for a timed three-hour run.