Mec-A2 — Kinematics and Dynamics of Machines

Kinematic and Dynamic Analysis: Graphical and analytical methods for kinematic analysis of planar and spatial mechanisms and elementary body motion in space, static and dynamic force analyses of mechanisms, gyroscopic forces, dynamics of rotating machinery, cam and gear mechanisms and specifications. Vibration Analysis: Free and forced vibration of undamped and damped lumped single and multi degrees of freedom systems with, analytical and numerical techniques of solution, viscous damping, vibrational isolation, vibration measurement and control.

Subject outline

Mec-A2 Kinematics and Dynamics of Machines is a Mechanical Engineering technical exam (PEO National Examination 16-Mec-A2) on how mechanisms move and on the forces and vibrations their motion sets up. The December 2018 and December 2019 papers examine mobility by Gruebler's equation, link types and the number synthesis of seven- and eight-bar chains; Grashof's criterion, transmission angles and the mechanical advantage of four-bar, inverted crank-slider and toggle linkages; velocity analysis by polygons and velocity images, on a six-link slider mechanism, a toggle press and an inverted crank-slider; acceleration analysis with the Coriolis component; cam design for a radial and an oscillating follower — choosing a motion law that satisfies the fundamental law of cam design, then the base circle and the pressure angle; planetary and compound planetary gear trains by the tabular method, with the number of planets that will fit; the shaking force of an inverted crank-slider and of a three-cylinder radial engine and how to balance them; and vibration — a block falling onto a mass–spring–damper, a pendulum rebounding from a wall, a beam carrying two masses stiffened by a spring, and the bounce and pitch of a patient bed sprung inside a helicopter. The study notes also cover instant centres and Kennedy's theorem, offset followers, flywheel sizing from the energy fluctuation, and vibration isolation and transmissibility.

The paper is 3 hours and open book. The December 2019 front page reads "This is an OPEN BOOK exam. Any non-communicating calculator is permitted." and "Five questions constitute a complete set. Every one answers question 1 in Part A, and one of the two questions in Part B, and chooses three additional questions from the remaining six." Part A holds Questions 1 to 6 and Part B Questions 7 and 8; the three mini-questions of Question 1 are marked [5], [10] and [5], the other questions [20], except Question 5, which prints no mark. The December 2018 front page reads "This is an OPEN BOOK exam and any non-communicating calculator is permitted." and "Every one answers question 1, and chooses three questions in Part A, and one question from part B. Question 1 is worth 40 points and each of the remaining questions are worth 20 points." There Part A holds Questions 1 to 5, Question 1 being four mini-questions of 10 marks each, and Part B holds Questions 6 and 7, with every question after Question 1 worth 20 points. Both papers ask the candidate to submit a clear statement of any assumptions made where doubt exists as to the interpretation of a question.

What this course gives you

Worked solutions — all fifteen questions, seven from December 2018 and eight from December 2019, every part, fully retypeset as live text and maths, with the final answers pulled out ahead of the working, each question's figure as printed on the official paper, and 41 authored diagrams and charts set into the solutions (19 for December 2018, 22 for December 2019) — mechanisms redrawn from the papers, velocity and acceleration polygons, cam laws, s-v-a-j curves and cam profiles, gear-train schematics, shaking-force plots and vibration responses. December 2019 has a published solution, mostly hand-written; it is transcribed with every number re-derived, and 14 published steps do not survive checking, at least one in each of the eight December 2019 questions, and each is flagged at the step that goes wrong with the published working quoted beside the correction. Several change the answer outright: the mechanical advantage of the Question 2 toggle press is published as infinite and is 18.1; in Question 3 the velocity of B is taken perpendicular to AoB as 156 m/s where the velocity image gives 144.5 m/s, the sliding acceleration is published as 21 462.61 m/s², about four times the 5 274 m/s² the acceleration polygon gives, and the published lengths are 1.54 times the drawing as printed, so the answers are also repeated at the paper's own scale; the Question 4 balancing scheme subtracts a crank-speed counterweight from the twice-crank-speed secondary force and claims 2025 N, an 18.25 % reduction, where the counterweight alone leaves the 225 N secondary, a 90.9 % reduction; the Question 5 cam uses constant velocity, whose infinite acceleration breaks the fundamental law, and is redesigned with a modified trapezoid rise (869 m/s² peak, 23.6° maximum pressure angle), while the published remedy for a large pressure angle runs the wrong way; the Question 6 speed ratio loses its sign and is −2.71, the output turning against the input; the second cycle of the Question 7 pendulum starts at 1.0130 s, not 2.0071 s; and the Question 8 bed is pitched about one end with its bounce mode left out, so the published stiffness range would put both modes inside the very excitation band it was meant to avoid. In Question 1 the link-type table is filled with joint counts, the non-Grashof loops are called rocker-rocker where they are triple rockers, and both sketched eight-bars contain a rigid sub-structure. Nothing is silently overwritten: the published value is kept beside the correction. December 2018 has no published solution: all seven of its answers are written for this course, and each question says so, including where the paper's own data fall short — Question 4 gives no tooth number for ring 3, which coaxiality fixes at 89, and its second stage cannot mesh at the common module the paper assumes. Study notes — ten condensed topics — mobility, link types and number synthesis; four-bar linkages, Grashof, the transmission angle and mechanical advantage; velocity polygons, velocity images and instant centres; acceleration and the Coriolis component; cam follower motion and the fundamental law of cam design; cam sizing by base circle and pressure angle, with oscillating followers; simple, compound and planetary gear trains; balancing, shaking forces and flywheels; free vibration of single-degree-of-freedom systems; and two-degree-of-freedom systems and vibration isolation — each naming the December 2018 and December 2019 questions it serves, with 23 authored diagrams and charts and 8 tables between them. Practice & case studies — ten multiple-choice questions, each with a worked explanation, and five longer problems with complete worked answers and 16 figures: an offset slider–crank by vector loop and polygons, all six instant centres of a four-bar with its velocity ratio and mechanical advantage, a rise–dwell–return–dwell cam designed to a 30° pressure-angle limit, and two engineering case studies, a flywheel and counterweight for a single-cylinder generator set and isolation mounts for an 1800 rpm compressor. All fifteen are written for this course; none is taken from the papers. Formula sheet — two pages, 35 relations in eight groups — mobility and number synthesis, four-bar linkages, velocity, acceleration, cams, gear trains, balancing and flywheels, and vibration. Both papers are open book with any non-communicating calculator, so the sheet is built to go into the exam with you, its relations grouped in the order the questions need them. Printable resources — ten one-page reference cards — mobility and number synthesis, four-bar Grashof and transmission, velocity polygons and instant centres, an acceleration and Coriolis checklist, cam motion laws with their peak factors, cam sizing by base circle and pressure angle, gear trains by the tabular method, balancing and flywheels, one- and two-degree-of-freedom vibration, and an exam-day plan — plus four blank exam stationery templates. Reference links — fifteen selected reference websites, among them the Engineers Canada syllabus page, PEO's technical exam program, MIT OpenCourseWare's Engineering Dynamics, Carnegie Mellon's free Introduction to Mechanisms, two NPTEL lecture courses, Cornell's Reuleaux kinematic model collection and the PMKS+ linkage tool, and fourteen chosen YouTube videos, each with a note on what it covers. Practice papers — the two question papers on their own, unmarked, ten pages each, for a timed three-hour run.